ones upon a game

I am almost exclusively a solo gamer and look at the gaming scene seen through those eyes. I also literally like alliteration. TWITTER: @onesuponagame
Recommend
21 
 Thumb up
1.00
 tip
 Hide

Friends! Romans! Mountain Climbers! Lend me your -eers!

Kevin L. Kitchens
United States
Gainesville
Georgia
flag msg tools
designer
Snowflakes Melt
badge
Snowflakes Melt
Avatar
mbmbmbmbmb
Recently I received my Kickstarter fulfillment copy of the collector's edition of Mountaineers by Massif Games, LLC. After first doing the requisite unboxing, I set it up to play. But unfortunately there were/are some issues with the 3D mountain and the turntable. A great idea for a game, but just a little awkward.

First off is the turntable itself. It's designed to be held in place to the main board via one of those two part grommet/connector devices that work great in many of Fantasy Flight Games like the dials in Star Wars: X-Wing Miniatures Game or the threat tracker in The Lord of the Rings: The Card Game. Whereas those items are designed to stay together once assembled, the turntable and board will not fold back up with the pin in place, necessitating removal (so don't press it too hard when putting it together!). Also each half of the connector is small, so it's hard to get it in place and then remove your hand before it drops through. Doable, but difficult.

The board really only needs a spindle, not a full connector. The turntable is not picked up during the game. So taking a clue from some others, I designed and 3D printed a new spindle that is about one inch tall and just sits easily under the main board. The post comes up through the board and then you can place the turntable over it. The weight of the turntable and normal (no table flipping!) gameplay easily keeps it on the post.




Not necessary, but I opted to add a large washer (this was actually from some light fixture and the piece was stashed in our tool box) between the board and turntable to give a little easier turning.

The spindle is available for free on Thingiverse and you can print yourself or order one printed.

Another problem though is the moutainside pieces. The tabs that go into the notches on the board are just a bit too shallow. They have to be because the turntable "rides" along the main board itself. So unfortunately as your placing pitons and moving climbers, you run the very real and very often risk of upsetting the board itself.

I had seen another user make a large triangle device to go over the mountain (for 1-4 players) and lock them in, but for me this didn't solve the issue of the board flexing inward during play. I had originally envisioned a complex replacement turntable with a spindle and arms and .... scrap that. This fellow's solution was a good first step, so I moved in that direction.

My solution simply involves cutting some pieces of craft of fun foam. I had a piece of black 5mm foam (found at Hobby Lobby or other craft stores) laying around and cut 1/4" strips from that. These I cut into 3" "cleats" and glued them to the turntable with the mountain assembled and in place. I used purple glue stick (which dries clear) and you have to be more patient as the foam takes a little longer to let the adhesive work. Once the outer perimeter was glued into place, I removed one panel and put cleats inside flush against the other two sides and then swapped out the third panel to get complete the inside bracing.





I turned the whole turntable over and put weight on it to make sure the glue cured and adhered well.

Now the panels are braced from any wiggly movement popping them out of the slots during rotation or gameplay. I had planned to go ahead and do the square 5-6 player mountain slots as well, but I had issues just getting that to even assemble normally. Since I would rarely play non-solo or above four players, I just left it for now and will explore that later.

Twitter Facebook
3 Comments
Subscribe sub options Fri Apr 19, 2019 6:20 pm
Post Rolls
  • [+] Dice rolls
Loading... | Locked Hide Show Unlock Lock Comment     View Previous {{limitCount(numprevitems_calculated,commentParams.showcount)}} 1 « Pg. {{commentParams.pageid}} » {{data.config.endpage}}
{{error.message}}
{{comment.error.message}}
    View More Comments {{limitCount(numnextitems_calculated,commentParams.showcount)}} / {{numnextitems_calculated}} 1 « Pg. {{commentParams.pageid}} » {{data.config.endpage}}